Refrigerator hook up water line, how to install a water line for a refrigerator
- Visit the download center to get a copy.
- After installation, check the water pressure by dispensing water.
- Adapt-a-Tees can be used in many situations where you need an extra line.
As mentioned above, the water supply line is not included with the refrigerator and is typically sold as a kit at your local hardware store if you don't have one already installed in your home. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. Social Support Contact us on Twitter or Facebook and we'll reply with an answer to your question or issue.
- Use pliers to untwist the faucet supply line from the cold water supply valve.
- Turn on the cold water faucet to drain any water left in the supply line.
- Find your water supply lines beneath your sink.
Connect and install the water line to your refrigerator
Again, hook the kit's instructions will tell you how to do this. How would you like to contact us? Then you'd need to twist the valve until it pierces your water line. Coil the excess water line behind the refrigerator. Leave the excess water line behind the refrigerator.
Tighten the fittings as needed, using channel-type pliers or an adjustable wrench. Run the new supply tube to the back of the refrigerator. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet.
Ask the Community Browse answers, ask questions and get solutions from other Samsung customers. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator. Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections.
Do not over-tighten it, as over-tightening will cause a leak. Disconnect the faucet supply tube from the shutoff valve. Check the connections, dating status meaning and tighten when necessary. Turn the cold water supply valve on beneath the sink. Learn more about Samsung promotions.
This Old House
If the refrigerator has a water dispenser, flush out several gallons to purge the line of all the air. An Adapt-a-Tee is an ideal plumbing fitting for this purpose. She attended Tarrant County College and studied English composition.
How to Hook Up a Water Line to a Refrigerator From the Sink
The kit provides you with the required parts to hook up a water line to your refrigerator. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. Turn the water supply valve on and check for leaks. Adapt-A-Tees are easy to install, and they provide the extra line you need with the least amount of work.
Twist the faucet supply line onto the female end of the adapter. If needed, you can install a booster pump to compensate for low pressure. First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink.
In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator. Install a new refrigerator water supply line. Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place.
How to Hook Up a Water Line to a Refrigerator
Keep in mind that you will need a compression nut at both ends, and some kits only come with one. If there is no water dispenser, speed dating company throw away the first full batch or two of ice to make sure it is all clean and ready to use. Question about a promotion?
Connect the line to the water line connector on the back of the refrigerator. If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. This image is also available in your user's manual. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel.
If your home doesn't have a water line installed from a previous refrigerator, you will need a water line that can run between the water pipes in your home and your fridge. Or continue shopping on Samsung. Thank you for your feedback!
Shut off the water at the valve that controls the cold-water supply pipe to the faucet. Disconnect the Existing Water Line. You can use the water line leftover from your previous refrigerator, or start fresh with a new kit from the hardware store. Turn the supply line on once again.
Tighten the connection just slightly more than hand-tight, using pliers. They come in various sizes to suit whatever situation you have. Thank you for visiting Samsung U. Slip the compression nut that came with the kit over the newly installed supply line. Connect the Supply Tube to the Refrigerator.
Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. Connect the water supply line to the refrigerator. Turn the water on and check for leaks.
Insert the new water line into the opening on the tee. The water lines are typically sold in kits and are not included with the refrigerator. Plug your refrigerator into the wall.
Other answers that might help. In the image, C demonstrates how it will look when installed. Watch for leaks at all the connections.